Guide to Choosing the Right Hairdressing Scissors

Step 1 – The handle

You will have seen before the traditional scissor handle design. It is straight, it’s even size, but it’s not designed for people.

You will also probably have seen the offset handle. With this scissor handle, one of many finger rings is shorter in size than the other. This is widely recognised as the superior type of hairdressing scissor and you may see why if you’re able to hold each together.

You would see that whilst the straight scissor is at 12 o’clock, the offset scissor is at 1 o’clock. This signifies that when you’re working – should you’re point cutting with a straight deal with scissor as an illustration, your elbow and your wrist are very high, which is quite uncomfortable and not a great posture. Whereas with the offset, it is way lower.

When you’re reducing towards skin, the straight deal with is quite obstructed and I will usually see stylists lifting the scissor off as they cut around the skin. However, with the offset handle there’s little or no obstruction in reducing against the skin.

If you want to taper to its simplest, you might select the offset Rotating Thumb Scissor, or what we call the Revo, Revolving Thumb scissor.

When you were to place it alongsideside any straight handle scissor, you would again see that the straight deal with scissor is open whereas the offset is closed. This is because the hole between your finger and thumb is larger, which places less pressure on the carpel tunnel nerve.

Secondly you’d notice the angle which you know makes the elbow lower. Third and most importantly, while you’re working on any haircut, slicing over the knuckles, it lets you drop your elbow, to a much more relaxed and comfortable position, which is going to avoid wasting loads of aches and pains.

Step 2 – The Blade

There are really only two types of scissor blades. The first are mainly made in Europe, usually Germany, they’re flat, the blades are straight, they’ve a beveled, virtually kind of a chiseled edge, and so they typically have serrations. These minimize like a guillotine. When the hair hits the blade, it cannot move and off it comes. They don’t slice lower, they only cut still.

Convex blades are very different. This has got a curve on the blade, it is hollow ground, it’s made from two pieces of metal, and instead of the European scissors which is made in in the future, this takes up to two weeks to make. The difference is with this you may slice cut as well as lower crisp, straight lines. These are acknowledged as a a lot superior type of blade.

Step three – The Type of Scissor

I would always recommend choosing a Long Blade, a Quick Blade, a Thinning Scissor, and a Layering / Texturiser scissor. With these 4 key “Tools of the Trade” you can take on any haircut in probably the most efficient way.

Numerous hairdresser will start their careers with the Brief Blade scissor, around 5″ in length. However lots will end their career with it too, by no means understanding the difference between blade lengths.

Should you can only use a brief blade, keep in mind it’s designed for use, initially, for cutting hair inside the fingers in the palm of the hand, and for reducing in opposition to the skin in very small, precise sections. That is OK should you try this kind of work.

But if you use a way where you create texture type haircuts, or if your minimize over the knuckles, the longer blade means that you can reduce there much more easily. In case you level reduce, the blade’s lengthy enough to go into sections.

A lot of hairdressers use a brief blade to cut over the knuckles. The problem is the blade isn’t as stable, and you will often see them go in a single, , three, and minimize the skin. Or in the event that they point minimize, they will move the scissor hand and really reduce off too much hair on the way in.

So bear in mind, in the event you do cut over the knuckles, a Longer Blade (6″ – 6.5″ in length) is going to give you a cleaner line much more safely, and in the event you level reduce, a much softer haircut without having to move your scissor hand.

I also recommend that every stylist use a 30 Tooth Thinning Scissor. What number of instances does a hairdresser need to remove weight from the hair without seeing any minimize marks? How many occasions do they need to blend two sections together? This is designed to get the proper finished result if you’re mixing together. Some of my clients really describe it as “evaporating” the hair away with no marks.

One other important piece of equipment is the 15 Tooth Layering / Texturising Scissor. This has important jobs; one is to create soft layers, and the other is to create texture.

The query is: what number of instances do you do a haircut that you just need to create soft texture?

Most stylists, those that have not been educated in regards to the 15 Tooth, will use a stable blade scissor, do the entire haircut, blow-dry it, and then go over and point minimize with the strong blade. In order that’s two hair cuts on one client.

Through the use of the 15 Tooth Layering / Texturising Scissor, you may get that lead to one go. It may be accomplished over your fingers, over your knuckles, or scissor over comb. This is probably probably the most underused, but groundbreaking products available in the world of hairdressing today.

If you have any kind of questions pertaining to where and just how to make use of The different types of hair scissors, you can contact us at our web page.

Leave a Reply